Post by fredAnyone got a cutter comp code sample, what does a Fadal use for
register? My post is out putting a H.
Like G41XxxxH8, should H be a D like Fanuc?
Thanks
P.S. where has all the CNC talk gone, the group looks like SPAM central
with all politics etc? Maybe time to move CNC to a new group.
I use H for height--parameter setting is "option 2" ( fanuc compatable ) and
D for diameter, so far as actual cdc entry into offset table it depends on
parameter setting whether you will enter as diameter or radius.
Also if you have a 4 or 5 axis machine then be sure and reset any A and and
or B fixture offsets back to zero whenever the table is not attached or else
you will experience problems with cutter comp failing to process.
Below is some code might help there is cutter comp on the smaller endmill
the program produces an internal cutout and fasterner holes for a 9 pin
conecter in .100 thick extruded al. Next time lokely I will combine drill
ops and do rough slot op using a combo mill-drill tool instead also there is
a bunch of m19 that are only there because of a temp work-around---appears
the particular machine was likely having some problem with orientination
during ATC cycle at that point in time.
%
N1O8410( NEW CONTROLLER BOX
N2(SA4162)
N3(USES E37)
N4(TO BE L0135 LIKELY)
N5( CONTROLLER FRONT MARCH 2008)
N6(CAUTION USES E37)
N7(THIS FILE CUTS THE D HOLE)
N8(TOOL CALL
N9M61( RELEASE HYD WORK CLAMPING
N10M0
( LOAD FRESH PART)
N11M60 (CLAMP)
N12M0
(VERIFY PROPER LOADING THEN CONTINUE)
N13G0G17G40G80G90M5M9H0Z0
N14T1M6(.375 DRILL)
N15E37S4400M3
N16D1H1Z3.
N17G40M8
N18G0X3.1576Y-0.4568
N19Z0.2
N20G81G98R+0.1Z-0.281F35.2
N21G80R+1.
N22G0Z3.
N23M19
N24M19
N25G0G17G40G80G90M5M9H0Z0
N26T2M6(THE SSTEP DRILL)
N27E37S4790M3
N28Z0.5D2H2M8
N29G0X2.8145Y-0.4568
N30G81G98R+0.1Z-0.25F6.1
N31Z-0.33F47.47X2.8145
N32X3.7985Y-0.4568Z-0.25F6.1
N33Z-0.33F47.47X3.7985
N34G80R+3.
N35G0Z0.5
N36M19
N37M19
N38G0G17G40G80G90M5M9H0Z0
N39T3M6(.375 EM RG)
N40E37S9000M3
N41Z0.5D3H3M8
N42X3.1576Y-0.4568
N43G1Z0.1F60.
N44G4P750
N45Z-0.2F51.
N46X3.4554Y-0.4568F9.
N47G0Z0.5F250.
N48M19
N49M19
N50G0G17G40G80G90M5M9H0Z0
N51T4M6(.1562 OR .1875 EM D4 CUTCOM)
N52E37S6750M3
N53Z0.5D4H4M8
N54X3.4554Y-0.4568Z0.2
N55G1G41X3.4184Y-0.2408Z-0.158F14.69
N56X3.0305
N57G3X2.9265Y-0.3448I0J-0.104
N58X2.928Y-0.3626I0.104J0
N59G1X2.967Y-0.5866
N60G3X3.0695Y-0.6728I0.1025J0.0178
N61G1X3.5435
N62G3X3.646Y-0.5866I0J0.104
N63G1X3.685Y-0.3626
N64G3X3.6865Y-0.3448I-0.1025J0.0178
N65X3.5825Y-0.2408I-0.104J0
N66G1X3.0305
N67G3X2.9265Y-0.3448I0J-0.104
N68X2.928Y-0.3626I0.104J0
N69G1X2.967Y-0.5866
N70G3X3.0695Y-0.6728I0.1025J0.0178
N71G1X3.5435
N72G3X3.646Y-0.5866I0J0.104
N73G1X3.685Y-0.3626
N74G3X3.6865Y-0.3448I-0.1025J0.0178
N75X3.5825Y-0.2408I-0.104J0
N76G1X3.1946
N77G40X3.1576Y-0.4568Z0.2
N78G0Z3.
N79M19
N80M19
N81G0G17G40G80G90M5M9H0Z0
N82T5M6(.125 COGSDILL DEBURR HOLES )
N83E37S5650M3
N84Z0.5D5H5M8
N85G0X2.8145Y-0.4568
N86G89G98R+0.1Z-0.49F45.P150
N87X3.7985Y-0.4568
N88G80R+3.
N89G0Z0.5
N90M19
N91M19
N92M61
N93G0G17G40G80G90Z0A0H0D0Y3.
N94T1M6
N95M99P1
%
7959